• Gender: Male
• Age: 56
• Designation: Senior Executive
• Highest Education Level: Graduate - Degree
• Preferred Country: India
• Preferred Location: Anywhere
• Work Experience: 32.3 Year(s)

Education

B.Tech.(MECHANICAL)fromS.V.HCO.LLEGEOF ENGINEERING , NAGARJUNA UNIVERSITY.
MBA(MARKETING)from PG Center kakinada, Andhra University.

Computer Knowledge:
Operating Systems Windows-2000, Windows-XP
Languages Packages C,MS-WORD,Powerpiont,Excell
CAD Packages Master CAD/CAM/CAE/Mold Flow.
CAE packages ANSYS 5.4, 7.0, 8.0, Ideas, Hypermesh, Nastran 2001

Skill Sets

Understanding the analysis requirements and translating it into FEA.
Interpreting the Results.
Preparation of Manual Calculation to cross check analysis Result,
if needed.
3D Mesh generation of complicated parts using brick elements.
Ability to work hard with a Zeal and Enthusiasm.

Work Experience

Engineer Product Design (FEA)
June 2005 to till date
Projects Profile
Title F400 sensor (mass flow meter) New Product Development project
Role Evaluating Design criteria for frequencies (Normal modes) and stress analysis, temperature analysis combined pressure and temperature analysis
Organization Emerson Design Engineering Centre
Software I-Deas, Nastran
Description
The sensor consists of number of parts like manifolds, flanges, tubes, case etc, the task is to mesh each and every part and assemble the mesh model, and run the analysis in Nastran, and Meshing is done on IDEAS 12 M3.
Projects Profile
Title F050 sensor (mass flow meter)
Role Solids meshing, analysis, Evaluating Design criteria for frequencies (Normal modes) and stress analysis
Organization Emerson Design Engineering Centre
Software I-DEAS, NASTRAN
Description
Design And development from concept to prototyping.
The sensor consists of number of parts like manifolds, flanges, tubes, case etc, the task is to mesh each and every part and assemble the mesh model, and run the analysis in NASTRAN, and Meshing is done on IDEAS

Title R200 sensor (mass flow meter)
Role Solids meshing, analysis, Evaluating Design criteria for frequencies (Normal modes) and stress analysis
Organization Emerson Design Engineering Centre
Software I-Deas, Nastran
Description
The sensor consists of number of parts like manifolds, flanges, tubes, case etc, the task is to mesh each and every part and assemble the mesh model, and run the analysis in NASTRAN, and Meshing is done on IDEAS

Title CMF 400 manifold
Role Solids meshing, analysis
Organization EMERSON DESIGN ENGINEERING CENTRE
Software I-DEAS, NASTRAN
Description
The task is to mesh the manifold part with parabolic tets and apply the pressure inside the flow channel and then apply the boundary conditions and run the solution in NASTRAN, Meshing is done in IDEAS.
Previous Experience :
Worked as a Project Assistant in the Department of FRACTURE MECHANICS (FML), BHEL (R&D), Hyderabad.

Projects in BHEL :
Title Stress analysis of SRL 254 compressor gear box.
Role 3D Modeling and Analysis.
Organization BHEL
Software I-DEAS, ANSYS
Description
The gearbox of SRL 254 compressor consists of upper casing and lower casing supporting three shafts of different weights and speeds. The gear and pinions are mounted on the shafts at different center distances; at the end of each shaft impellers of different weights are attached. At each stage different gas pressures are also acting. The modeling and meshing is generated using I-DEAS and the stress analysis is done in ANSYS.

Title Complete Modeling And Assembly Of Srl 254 Compressor Gear Box
Role 3D Modeling and assembly
Organization BHEL
Software I-DEAS

Description
The gear box of SRL 254 compressor consists of upper casing ,lowercasing, oil seals ,bearings, HS1 SHAFT, LS SHAFT, HS2 SHAFT,PINIONS,bearings,junction box, lubricant pipes, dial gaugesetc.All these parts are modeled and assembled in IDEAS 11NX .

Title Response analysis of SRL254 compressor GEARBOX CASING.
Role 3D Modeling,and anlysis
Organization BHEL
Software IDEAS ,ANSYS 7.0
Description
The response anlysis of SRL 254 COMPRESSOR GEAR BOX was modeled using IDEAS,and the response analysis was done done both
In ideas, and ansys.Here the mode shapes and frequencies are obtained.

Title handle for SM 63 fuse holder
Role 3D Modeling
Organization Thread Aid Industries.
Software PRO-E 2001
Description
The fuse holder is a general-purpose electrical appliance. The 3D model is generated from the 2 D views using pro-e 2001.

Incharge Engineer
1994 to 1995
Worked Siddartha Kartik Industries, Bangalore.

Trainee Engineer
1992 to1993
Worked with Ozna Plastic Works, Secunderabad.A.P
Job Profile
Worked as a supervisor in the shop floor, developed 2D Drawings using auto cad Rel 10.

Future Goals

Looking forward to an organization that offers stimulating and learning environment to pursue challenging career in the area of Engineering Analysis (FEA).